For HE4K-01 / HE4K-R4 / MVE-150 / MVE-100R / SME-01 / DME-02/03/04 use Z3-TI-http_api

For firmware version 5.X and higher

To read configuration variable, simply perform an HTTP GET to the URL

http://server_address/cgi-bin/control.cgi

with the body as given below.

The reponse will be in JSON format, giving the value of each variable.
To read global configuration variables, GET with this body:

ctrl=sys&chn=null

To read encoder channel configuration variables for channel 1, GET with this body:

ctrl=enc&chn=1

Python example code for reading configuration:

import requests, json, sys

server_url='http://192.168.0.120/cgi-bin/control.cgi'

global_cfg = requests.get(server_url, params='ctrl=sys&chn=null')
print global_cfg.json()

enc_cfg = requests.get(server_url, params='ctrl=enc&chn=1' )
print enc_cfg.json()

Sample output:

>>> print global_cfg.json()
{u'ipmtu': 1500, u'vid_port': u'microhdmi', u'macaddr': u'40:cd:3a:04:f0:c3', u'logo_enable': u'off', u'wifi_exists': True,
u'processor_id': u'QCS605', u'ddns_password': u'', u'model_enable': u'off', u'enc_current_preset': u'encoder',
u'default_gw': u'192.168.0.1', u'disp_std': u'auto', u'session_id': u'---', u'ddns_provider': u'freedns',
u'ptp_role': u'auto', u'timezone': u'CST6CDT,M3.2.0,M11.1.0', u'MODEL': u'Z3-Q603-HD', u'opstate': u'RUNNING',
u'hwversion': u'Z3-Q603-HD', u'ddns_enable': u'off', u'disp_input': u'primary', u'board_id': u'0xFF10',
u'termserve_remote_enable': u'on', u'hwserial': u'30010110194010011', u'console_enable': u'on', u'enable_ptp': u'false',
u'camera2_if_type': u'Unused', u'local_netmask': u'255.255.255.0', u'ret': u'0', u'logo_width': 319, u'MIC_analog_gain_db': 5,
u'camera1_if_type': u'Sony_LVDS', u'opmode': u'encoder', u'syspassword': u'', u'local_dnsip2': u'0.0.0.0',
u'ddns_hostname': u'', u'use_dhcp': u'0', u'enc_vivpss_mode_enable': u'off', u'pe3': u'', u'z3_termsrv': u'enabled',
u'MICL_analog_gain_db': -20, u'preview_auto_start': u'1', u'pe7': u'', u'logo_height': 156,
u'sensor_serial': u'30010310194010011\n', u'ddns_username': u'', u'eth_speed': u'AUTO', u'nfs_enable': u'off',
u'nfs_server': u'192.168.1.6', u'z3_avmux': u'enabled', u'nmea_enable': u'off', u'z3_sntp': u'enabled',
u'eth_duplex': u'AUTO', u'z3_fec_enc': u'enabled', u'z3_webproxy': u'enabled', u'enc_adv_setting': u'off',
u'do_autostart': 1, u'enc_channels': u'1', u'pe8': u'', u'local_dnsip': u'192.168.0.1', u'local_ip': u'192.168.0.14',
u'pe4': u'', u'pe5': u'', u'pe6': u'', u'diff_serve': 0, u'pe0': u'encoder', u'pe1': u'', u'pe2': u'',
u'nfs_server_root': u'/c/media', u'enable_snmp': u'false', u'fpgafileglob': u'', u'enable_sntp': u'true',
u'sysdevicename': u'Z3-Q603-HD', u'sntp_servers': u'pool.ntp.org', u'zfinder_enable': u'on', u'model_name': u'Z3-Encoder',
u'hw50serial': u'50010110194010011', u'visca_present': u'true'}

print enc_cfg.json()
{u'vmulticastdest': u'225.1.2.3', u'tslowlat': u'on', u'klvmuxmethod': u'sync', u'srt_destAddr': u'192.168.0.6',
u'vcrop_height': 1080, u'zixifecblock': u'50', u'telopcharsize': u'32', u'source_status_str': u'+CAMERA 1920x1080p 60.00 fps\n',
u'vratectrl': u'cbr', u'rotate_angle': 0, u'zixisession': u'test', u'asource': u'CAMERA', u'aport': u'8700', u'pmtpid': 31,
u'authonoff': u'off', u'srt_encrypt': 0, u'vcodec': u'h265', u'klvmode': u'sdi', u'auxonoff': u'off', u'channel': 1,
u'mounts': u'', u'vcrop_width': 1920, u'vcrop_x': 0, u'vcrop_y': 0, u'amulticastdest': u'225.1.2.3', u'vprofile': u'high',
u'klvsrc': u'/dev/gv7601.0', u'auth_passwd': u'password', u'teloplocation': u'top_left', u'gps_overlay_device': u'/dev/ttyAMA0',
u'ret': u'0', u'klvserialbaud': u'115200', u'rtsp_auth_password': u'admin', u'zixirateadjen': u'on', u'zixiauthen': u'off',
 u'vinterlacemode': u'combine', u'vgopsize': 60, u'mmulticastdest': u'225.1.2.3', u'vcrop_enable': u'off', u'klvenable': u'off',
u'preset': u'actv_preset', u'mport': u'8800', u'auth_user': u'user', u'gps_overlay_enable': u'off', u'zixioverhead': u'15',
u'tsrate': u'5000K', u'enc_status': u'RUNNING', u'pcrinterval': 50, u'aptspcr': 250, u'filesize': u'1024M', u'klvbrate': u'1000',
u'acodec': u'fdk_aaclc', u'lowdelay_opt': u'off', u'apid': 120, u'zixilatency': u'500', u'rtsp_auth_enable': u'off', u'srt_mode': 0,
u'klvpid': u'35', u'nfstrength': u'0', u'vbitrate': u'4M', u'rtsp_auth_username': u'admin', u'zixiuser': u'user',
u'gps_overlay_location': u'top_right', u'vprotocol': u'rtsp', u'feconoff': u'off', u'vdelay': 1000, u'vsource': u'CAMERA',
u'fprefix': u'MOV1_%C', u'telopenable': u'off', u'teloptext': u'Z3-Q603-HD', u'storage': u'/media/sda1', u'vquality': u'balanced',
u'asamplerate': u'1', u'vgdr': u'off', u'rotate_enable': u'off', u'avmux_index': u'streaming', u'abitrate': u'128000', u'vpid': 221,
u'feccol': 5, u'gps_overlay_char_size': u'32', u'vframeratediv': 1, u'pipenable': u'off', u'vres': u'follow_input', u'pcrpid': 521,
u'aenable': u'off', u'apair': 0, u'piplocation': u'top_right', u'rtmp265_enable': u'off', u'srt_pass': u'password1234',
u'vdest': u'192.168.0.6:8600', u'fecrow': 1}

Description: Enable audio channel

Possible values: yes, no

Description: Audio encoder algorithm selection

Possible values: dsp_aaclc, fdk_aaclc, fdk_aache, fdk_aache_v2

Description: Audio encode bitrate

Possible values: Depends on codec; in units of bits per second

Description: Audio sample rate

Possible values: 48000, 44100

Description: Select audio input

Possible values: MICL (microphone, line input levels)

               MIC    (unpowered microphone levels)
               HDMI   (microHDMI input, for HE4K-DCK/FV4K-13A only)
               HD-SDI (SDI input, for DME-10/FSDI-DCK/FSDI-13A only)

Description: Audio PID for transport stream.

Possible values: 32 to 8191 - must not conflict with other PID assignments.

Description: Destination UDP port for RTP audio

Description: For transport stream modes only – intial PTS to PCR offset for audio, in milliseconds

Possible values: 100 to 2000

Description: Password for RTMP authentication.

Description: Username for RTMP authentication.

Description: Enable or disable RTMP authentication. Default: off Possible values: on, off

Description: Encoder channel number

Possible values: 1, 2, 3

Description: Column count for ProMPEG.

Possible values: integer greater than 1

Description: Enable ProMPEG if supported.

Possible values: on, off

Description: Row count for ProMPEG.

Possible values: integer greater than 1

Description: Size of TSFILE or AUX file recording, in bytes.

A “K” suffix indicates kilobytes (thousands of bytes/second).

A “M” suffix indicates megabytes (millions of bytes/second).

Description: Relative filename for TSFILE or AUX file recording. Note that “fprefix” does NOT include the absolute media path – the “storage” parameter is the proper place to specify the absolute media path.

Absolute path to mounted media device (e.g. /media/sda1/)

For MP4 recording only. Possible values: normal, streaming

normal means MOOV atom at the end of file.

streaming means MOOF atoms interspersed throughout the file, which is more tolerant of errors and truncated files.

streaming is recommended for most recording scenarios. Only select “normal” if you want conventional MOOV atom at the end of file, if some legacy tool or decoder requires it.

OSD overlay text character size in pixels

Possible values: 16, 32, or 64

Enable or disable telop (i.e. OSD overlay of text).

Possible values: on, off

Where to overlay text in the encoded video

Possible values: top_left top_right top_center bottom_left bottom_right bottom_center

Text string for OSD overlay

Description: Distance between I frames (key frames) in GOP sequence

Possible values: 1 through 240

Description: Video bitrate in bits per second.

Possible values: A “K” suffix indicates kilobits (thousands of bits/second).

A “M” suffix indicates megabits (millions of bits/second).

Note: In UDP transport stream case, the tsrate should be set

higher than the vbitrate, with at least 15% margin.

Description: Video maximum burst size in milliseconds.

Possible values: 100 to 2000

Description: Destination URL address for encoded bitstream. May be interpreted differently depending on “vprotocol” setting.

For UDP and RTP transports:

client_ip:client_port

For RTMP transport:

 server_ip[:server_port]/application/streamname

Description: Divide video input frame rate by this number to get encode frame rate.
The encoder will discard (frameratediv-1) out of (frameratediv) frames.

Possible values: 1, 2, 3, 4, 5, 6

Description: Enable or disable Gradual Data Refresh. Reduces I-frame size (reduces latency). At lower bitrates, a horizontal rolling artifact may be visible.

Possible values: on, off

Description: Specifiec which codec to encode with.

Possible values: h265, h264, mjpeg

Description: H.264 profile (see https://en.wikipedia.org/wiki/H.264/MPEG-4_AVC#Profiles​ for full description)

Possible values: baseline, main, high

Description: Protocol used to transport the encoded bitstream.

Possible values: rtp, rtmp, udp, asi, tsfile, mts, tsrtp

Description: Set balance between low latency, and higher quality+bitrate compliance.

Possible values: lowlat, balanced, high

Description: Rate control mode for encoder.

Possible values: cbr, vbr

vbr mode may be burstier than cbr.

Description: Video resolution

Possible values: follow_input preserve video source resolution, no resize

               WxH           resize to width W and height H

Description: Video input from which encoder will source its video

Possible values: Board-dependent

Description: Enable PIP of channel 2 on channel 1 encode. Only available on FV4K/FV2K/FSDI

Possible values: on, off

Description: Sets the location of the PIP on channel one. Only available on FV4K/FV2K/FSDI

Possible values: top_left, top_right, bottom_left, bottom_right

Description: Sets the interlaced mode for the video input

Possible values: combined, separated (H265 only)

Description: video multicast destination for RTSP. Used by ONVIF StartMulticast/StopMulticast functions

Possible values: valid multicast addresses

Description: audio multicast destination for RTSP. Used by ONVIF StartMulticast/StopMulticast functions

Possible values: valid multicast addresses

Description: enables/disables rtsp authorization for stream

Possible values: on, off

Description: username for rtsp authorization

Possible values: alpha numeric string

Description: password for rtsp authorization

Possible values: *

The following parameters only apply to transport stream encoding (transport is set to udp, asi, tsfile, mts, or tsrtp).

Description: Video PID for transport stream.

Possible values: 32 to 8191 – must not conflict with other PID assignments

Description: Audio PID for transport stream.

Possible values: 32 to 8191 – must not conflict with other PID assignments

Description: PCR PID for transport stream.

Possible values: 32 to 8191 – must not conflict with other PID assignments

Description: PMT PID for transport stream.

Possible values: 16 to 31 – must not conflict with other PID assignments

Description: Transport stream total transport rate in bits per second.

Possible values: The 'K' suffix indicates kilobits (thousands of bits/second). The 'M' suffix indicates megabits (millions of bits/second).

Note: In UDP transport stream case, the tsrate should be set higher than the vbitrate, with at least 15% margin.

Description: Low latency transport stream mode (VBR).

Possible values: off, on

Describe: Enable AUXillary file recording in UDP mode – allows simultaneous UDP streaming and TS file recording on the same channel. Only valid if transport is UDP and tslowlat is off

The path to storage is set by the “storage” parameter.

The filename is set by the “fprefix” parameter. The default value is “MOV1_%F_%T”. The “%F” specifier inserts a date stamp, and the “%T” specifier inserts a time stamp.

The recording file size is set by the “filesize” parameter. When the file reaches this size, a new file will be created.

Description: Bitrate to allocate in transport stream for KLV data.

Description: Enable KLV capture from SDI, UART or debug file, if supported.

Possible values: off, on

Description: Type of KLV source device, whose path is specified in klvsrc

Possible values: sdi, serial, file

Description: If klv_mode is serial, specify the baud rate

Possible values: 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200

Description: Select synchronous or asynchronous transport stream KLV multiplexing, as specified in MISB ST 1402

Possible values: sync, async

Description: PID for KLV data in transport stream

Description: Source device for KLV metadata

Description: Interval between PCR packets in milliseconds.

Possible values: 30 - 100

Python example code for starting/stopping all channels:

import requests, json
import sys, getopt

actionname='StartChannel'

server_url='http://192.168.0.120'

control_cgi_url = server_url + '/cgi-bin/control.cgi'

payload = 'ctrl=sys&chn=null'
sysctrl = requests.get(control_cgi_url, params=payload)

j = sysctrl.json()
print j

enc_channels_string = j['enc_channels']
opmode       = j['opmode']

enc_channels = enc_channels_string.split( ',' )

print 'enc_channels', enc_channels, 'opmode', opmode

channel_list = enc_channels

for channel in channel_list :
    # Remove leading C
    if channel[0:0] == 'C':
        channel = channel[1:]
    print actionname, ' ', opmode, 'channel', channel
    payload = 'action='+actionname+'&'+ 'chn=' +channel+'&' + 'loadfromdb=true';
    headers={'Content-Type':'application/x-www-form-urlencoded; charset=UTF-8'}
    r = requests.post(control_cgi_url, data=payload, headers=headers)

    print r.text

The “loadfromdb=true” parameter will load the current settings from the database.

If you omit the loadfromdb parameter, *none* of the database settings will be used – any parameters you do not supply, will be set to default values.

For example, this is what a StartChannel request from the web server looks like:

action=StartChannel&chn=1&vsource=&vres=follow_input&vcodec=h265&vgdr=on&vprofile=high&vratectrl=cbr&vbitrate=2M&vframeratediv=1&vgopsize=60&vprotocol=rtsp&vdest=192.168.0.6:8600&storage=&fprefix=MOV1_%F_%T_&vpid=221&vdelay=1000&pcrpid=521&pcrinterval=50&pmtpid=31&tsrate=3000K&tslowlat=on&feconoff=off&fecrow=1&feccol=5&zixioverhead=15&zixiauthen=off&zixisession=test&zixiuser=user&aenable=on&asource=MICL&acodec=fdk_aaclc&abitrate=128000&asamplerate=48000&aport=8700&apid=120&aptspcr=250&klvenable=off&klvmode=sdi&klvsrc=/dev/gv7601.0&klvpid=35&klvbrate=1000&authonoff=off&auth_user=user&auth_passwd=password&auxonoff=off&filesize=1024M&telopenable=off&teloptext=ENCDEV&teloplocation=top_left&telopcharsize=32&vquality=balanced

Add new channel tab. Check the channel number is valid or not, for e.g. the channel number can be max (1 to 4)

and if so then we check whether the preset values are available for this channel number, then we will be reading from the PRESET_TABLE of the database.

If not, then we will adding the default values for this channel.

Insert decoder history in the database

Input : channel number, URL

Output : Add the information in the decoder history table in the database

Input : read the camera index ( value can be 1 or 2)

Output : provide the camera information. if camera index is 1 then check whether camera type is (Visca/tau/boson)

If camera index is 2 then check whether camera type is (Visca/tau/boson/tamarisk/CameraLink_CVBS/sdi)

Send control commands to camera.

Only one command can be sent at a time; the list below are the only supported VISCA commands through the HTTP API. To use VISCA commands that are not listed, usage of the TCP socket can be used to send those VISCA commands.

API Format:

action=CameraControl&interface=Visca&command=visca_command&cam_index=1

interface possible values: Visca, Tamarisk, Tau2, Boson, Genlock (default: Visca)

example:

Commands without value assignments

action=CameraControl&command=dzoom_off&cam_index=1

Commands with value assignments

action=CameraControl&command=set_monitor_mode 1080p-59.94&cam_index=1

The Visca commands use the same syntax as the serial menu “V” command, as shown below

For the most current list of VISCA commands supported press “V” from the Serial/SSH session of the Serial Menu.

auto_icr_disable
auto_icr_enable
cam_control_inquiry
cam_custom_recall
cam_custom_reset
cam_custom_set
chroma_get_suppress
chroma_suppress      Set Chroma Suppression  (0=none, 1 to 3=chroma supression strength)
clear_if
color_gain           Set Color gain (0=60%, 14=200%)
color_get_gain
color_get_hue
color_hue            Set Color hue (0=-14 degrees, 14=+14 degrees)
debug_rx
dzoom_combine_mode
dzoom_direct         D-Zoom Position (0x00 to 0xeb)
                     * Enabled during Separate mode
dzoom_off
dzoom_on
dzoom_separate_mode
dzoom_stop
dzoom_super_res
dzoom_tele_var       p = 0 (Low) .. 7 (High)
                     * Enabled during Separate Mode
dzoom_wide_var       p = 0 (Low) .. 7 (High)
                     * Enabled during Separate Mode
dzoom_x1_max
eflip_off
eflip_on
ext1_func_inquiry
ext2_func_inquiry
ext3_func_inquiry
focus_auto
focus_direct         focus pos
                     Min. 0x1000 Over Inf
                     0x2000 10m
                     0x3000 5m
                     0x4000 3.3m
                     0x5000 2.5m
                     0x6000 2m
                     0x7000 1.7m
                     0x8000 1.5m
                     0x9000 1m
                     0xa000 50cm
                     0xb000 30cm
                     0xc000 15cm
                     0xd000 6cm
                     0xe000 1cm
focus_get_mode
focus_get_pos
focus_manual
focus_near_limit     focus near limit
                     Min. 0x1000 Over Inf
                     0x2000 10m
                     0x3000 5m
                     0x4000 3.3m
                     0x5000 2.5m
                     0x6000 2m
                     0x7000 1.7m
                     0x8000 1.5m
                     0x9000 1m
                     0xa000 50cm
                     0xb000 30cm
                     0xc000 15cm
                     0xd000 6cm
                     0xe000 1cm
focus_stop
focus_tele_std
focus_tele_var       p = 0 (Low) .. 7 (High)
focus_toggle
focus_wide_std
focus_wide_var       p (0 (Low) .. 7 (High))
get_low_delay_mode   Get low delay mode: 0 - normal, 1 - low delay
get_monitor_mode     get_monitor_mode: Get video mode of camera output
help
high_sensitivity_off
high_sensitivity_on
icr_mode             modes:
                     auto
                     on
                     off
                     threshold [0-255]
lens_control_inquiry
lens_get_temp
lr_reverse_off
lr_reverse_on
other_inquiry
power_inquiry
power_off
power_on
register_read        Read internal register.
register_write       Write internal register.
                     * Note: To make register changes effective, run power_off and power_on
set_address
set_low_delay_mode   Set low delay mode: 0 - normal, 1 - low delay
set_monitor_mode     Set monitor mode.
                     List of modes: 1080p-25
                     720p-50
                     720p-59.94
                     2160p-25
                     2160p-29.97
                     1080p-29.97
                     1080p-59.94
                     1080p-50
slow_shutter         modes:
                     on
                     off
limit [0-255]
trace                enable (0=off, 1=on)
version_inquiry
wb_auto_mode
wb_autotrace_mode
wb_get_bgain
wb_get_mode
wb_get_mode_name
wb_get_rgain
wb_indoor_mode
wb_manual_bgain_direct Set Manual WB BGain (0..255)
                       * Enabled during Manual WB mode
wb_manual_bgain_reset
wb_manual_mode
wb_manual_rgain_direct Set Manual WB RGain (0..255)
                       * Enabled during Manual WB mode
wb_manual_rgain_reset
wb_onepush_mode
wb_onepush_trigger
wb_outdoor_auto_mode
wb_outdoor_mode
wb_sodium_lamp_auto_mode
wb_sodium_lamp_fixed_mode
wb_sodium_lamp_outdoor_mode
zoom_direct          pos
                     Min. 0x0000
                     Max. 0x4000 (In Separate mode)
                     Max. 0x4000 (In Combine mode and DZoom=Off)
                     Max. 0x59C0 (In Combine mode, DZoom=Super Resolution Zoom, and monitoring mode QFHD)
                     Max. 0x6000h (In Combine mode, DZoom=Super Resolution Zoom, and monitoring mode FHD or less)
                     Max. 0x7AC0h (In Combine mode and DZoom=On)
zoom_get_pos
zoom_stop
zoom_tele_std
zoom_tele_var        p = 0 (Low) .. 7 (High)
zoom_wide_std
zoom_wide_var        p (0 (Low) .. 7 (High))

With dual VISCA camera supported added we need to tell the API which camera we want to talk to. this is done with cam_index

The values accepted are either 1 or 2

delete the decoder history

input : channel number

output : Delete the channel number from the DECODER_HISTORY_TABLE of the database

delete the channel tab and update the PRESET_TABLE of the database.

delete each row of the preseting value of encoder or decoder based on the get_opmode from the PRESET_TABLE

Output: Disconnects the Wifi Network

​Encoder channel to apply dynamic command to.

var

Variable to modify dynamically. Possible values: vratediv, vrate, gop, analog_gain, telop_text, pip_enable, pip_location, startmulticast, stopmulticast

Value to set dynamic variable to.

chn: Encoder channel number

dec: Device name as in storage

Output: un mounts the device to eject in safe

moving the preset value from the existing table to a new table and erasing the existing table

create a z3export.db and copy the presetting value of encoder or decoder based on the get_opmode of the PRESET_TABLE

Erase configuration database.

Optional arguments: reset_ip (default value:0): 1=clear IP settings, 0=keep IP settings

This command erases the config database. To generate the factory settings, you must reboot the system, either using the “RestartBoard” action or power-cycling the system.

mnt_point: storage media device node path which needs to be formated

file_system: File system type to be used with mkfs

Output: Formats the given media in FAT filesystem format and mount it

Read the value of color table using the system call and pixel format

from the fpga.

Get the camera tab index the values are (1 / 2) and camera type. The camera types are (Visca / tau / boson / tamrisk)

if camera index is 2 , then the camera type (Visca / SDI)

Read the camera tab index.

Based on the camera index and camera type the corresponding html file will be read. The html files are located in the /opt/webgui/*.html

The html files are visca.html / flexio.html

return the encoder status

input : channel_number

Output : The encoder status can be running / couldn't deduct input on camera / idle / Stopped.

The encoder status values are stored in this path /tmp/enc_1_status.

Get the sensor id and based on the sensor id, we read the video inputs from the VIDEO_INPUT_TABLE.

The video input table has the sensor id, video port (which is CAMERA1/ CAMERA2) the camera type (SONYLVDS/ LT6911 / MIPI) and so on.

retrieve the wifi password.

Input

ssid: read Wifi Access point name

Output: Returns the Wifi password, generally it will be stored in this path /var/run/wpa_supplicant.pid.

Input : data

read the data: Query Ins

Output: Returns the YawAngle, PitchAngle or RollAngle

Input : data is parsed using JSON format in PtzAuxiliary. Here we read the auxillary ID and auxillary is set or not.

Output: Save the auxillary id and set

Load the active preset value from the PRESET_TABLE and update

Read the current preset values, which is encoder/decoder and number of channels based on the device type.

for e.g if the device is FV4K_DCK_15 / FV4K_13A / FV2K_13A then the maximum preset encode channels will 1 and 2.

Output : update the current_preset values in the STATE_TABLE in the database.

set the password value for login user.

Json data wich contains nonce and name of the user

Output: Remove digest entry for this user

Add/Update overlay

​Encoder channel to add overlay to.

​Index to map overlay to.

Type of overlay to be used possible values: text or png.

In the case of text overlay this would be the source text for png overlay this is the path to the png on the encoder. Images must be uploaded to board to be used.

This is the location of the overlay. Possible values: 'top_left', 'top_right', 'top_center', 'bottom_left', 'bottom_right', 'bottom_center', 'x,y' (negative numbers not supported for x or y)

For text overlay this is the character size. Possible values: 16,32,64

This will set the layer for the overly higher numbers will overlay over lower numbers if overlapping.

Sets the transparency of the text. Possible values: 0-255

​Encoder channel to remove overlay from.

​Index of overly for this channel.

Send absolute move command to the PTZ.

parse the data using json format and retrieve the mode, position and speed value. The mode values can be PanTilt / Zoom / Both.

Output: Updates the PTZ speed and position value for absolute move

clear the Ptz preset values

parse the data using json format and retrieve the profile token, preset token, username and token.

Output: remove the PTZ preset value for the username, token

Pan to the left at half speed

  action=PtzContinuousMove&data={"PanTilt":{"x":-0.5,"y":0},"idx":0}

Pan to the right at half speed

  action=PtzContinuousMove&data={"PanTilt":{"x":0.5,"y":0},"idx":0}

Tilt down at max speed

  action=PtzContinuousMove&data={"PanTilt":{"x":0,"y":1},"idx":0}

Get the authentication user name

parse the data using json format and retrieve the profile token, preset token, username and token.

Output: set the preset value of Ptz.

Get the new tour spot

parse the data using json format and retrieve the profile token, preset token, mode, angle and speed. The mode values are Pan / Tilt

Output: set the new tour spot

move the Ptz to the input position

parse the data using json format and retrieve the mode, angle and speed. The mode values are Pan / Tilt

Output:Updates the PTZ position value

Preset the Ptz based on the value parsed from the json object.

parse the data using json format and retrieve the value.

if the data value 0

remove the preset,

if the data value 1

set the preset

if the data value 2

Goto the preset

Output: Remove or updates the PTZ position based on the data value.

Get the ptz status degree value.

parse the data using json format and querry from the ptz for position of x, y and z value.

Output: Based on the ptz query we will be knowing whether its Tilt Angle or Pan Angle

Remove the ptz tour spot

parse the data using json format and retrieve the profile_token, tour_token, and row_index

Output: Remove the existing tour spot from the ONVIF_PtzTourSpots table in the database

Get the user information which provides user name, user level, and nonce.

parse the data using json format and retrieve the profile_token, preset_token, and username, and token

Output: Sets the PTZ preset value for current user

Get the user information which provides user name, user level, and nonce.

parse the data using json format and retrieve the profile_token, preset_token, and username, and token

Output: Start the new Ptz tour

Stop pan and tilt

  action=PtzStop&data={"mode":1,"idx":0}

Remove / delete the jobs from the schedule.

Read the job index and job name

Number of rows of the schedule job.

Delete the jobs in the /opt/config/z3schedules/root/ in the system and also update in the SCHEDULE_TABLE in the database.

Reboot the board

Save camera-related settings below.

Description: Set camera zoom

Possible values: 0 (wide) to 0x7ac0 (full zoom)

Possible values: auto. indoor, outdoor, onepush, autotrace, manual, outdoor_auto,

               sodium_lamp_auto, sodium_lamp_fixed, sodium_lamp_outdoor

Possible values: Range from 0 (60%) to 14 (200%)

Possible values: Range from 0 (60%) to 14 (200%)

Possible values: 0=none, 1, 2, 3

Possible values: 0 to 255

Possible values: 0 to 255

Possible values: 0, 1

Description: Set manual camera focus distance Possible values: 0x1000 to 0xf000

Description: Set focus mode

Possible values: auto, manual

saves the camera boson settings

reads the color pallete value

Save the camera DRS tamarisk settings in the CAMERA_BOSON_TABLE in the database

saves the camera DRS Tamarisk settings

reads the color pallete value

Save the camera DRS tamarisk settings in the CAMERA_DRS_TAMARISK_TABLE in the database

saves the camera Link settings

reads the pixel format and color table value

Save the camera DRS tamarisk settings in the CAMERALINK_TABLE in the database

Saving the CameraLx settings value and update in the CAMERA_LX_TABLE in the database

read the value of exposure mode, shuter speed , exposure component settings, whitebalance, ISO, Color Temp, NtscPalSelection, MovieSteadyMode

used in the camera settings

saves the camera TAU settings

reads the color pallete value from this path /tmp/currentlut*.txt and also reads the active color table

Save the camera TAU settings in the CAMERA_TAU_TABLE in the database

Read the values from the schedule tab and save the jobs

The data contains multiple values, such as

enable/disable of schedule

Name of the job

Function are (Start-Encoder / Stop-Encoder / Snapshot / PTZ Preset / PTZ Tour / Reboot)

Channel (Ch1 / Ch2 / Ch3 / Ch4)

Options about the time, which can be (Every Minute / hours / day / Week/ Month/ Yearly / custom )

Number of rows of the schedule job.

Save the jobs in the /opt/config/z3schedules/root/ in the system and also update in the SCHEDULE_TABLE in the database.

check whether the mode is decoder or encoder using get_opmode()

save the encoder preseting value in the PRESET_TABLE

save the decoder preseting value in the PRESET_TABLE

Output : Update state setting table in the database

Save current settings to non-volatile memory, so they will be used on the next startup.

Control advanced settings display on WebUI.

Possible values: off, on

set the password for the Wifi network

read the password to connect with the WIFI network

Enable/disable the password to connect with WIFI

Output: Set the wifi password and password enable flag and check if the wlan0 status in in Connected or AP

Set the analog mic decibal value

analog gain decibal value where the (Range are -97 to 30)

Output : update the audio gain value in the AUDIO_INPUT_TABLE in the database

Set the value of color table and pixel format.

The value for the color table and pixel format

The option can be color table or pixel format.

Output : Update the value for the color table and pixel format in the CAMERALINK_TABLE in the database.

set the console value as ttyAMA0 or none.

“on” to enable or “None” to disable the console device for the log prints

Output: Set the console value.

Dynamic DNS settings.

Set logging level. The setting is persistent.

Possible values: 0=None, 1=Error, 2=Information, 3=Diagnostics, 4=Codeflow, 5=Dataflow

Note: Dataflow debug is for debug only, and not recommend for normal system operation.

Set the device name

Read the device name

Output: update new device name in the STATE_TABLE in the database

Controls composite output (passthru video from camera)

Set display standard for composite output

Possible values; auto, ntsc, pal

set the DSCP configuration value

Read the DSCP configuration value. The values are (Expedited Forwarding / Multimedia Conferencing / Multimedia Streaming / Low-Latency Data ) and so on.

Output :

Set the DSCP configuration value and update in the STATE_TABLE of the database.

Set the fpga value.

read fpga value, the values can be (boson/cvbs/tamarisk/tau2)

Output : update fpga value in the STATE_TABLE of the database

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc. Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.

do_autostart Control automatic stream start after bootup. Possible values: 1 = do autostart 0 = do not autostart.

enc_adv_setting Control appearance of advanced settings on WebUI. Possible values: off, on.

ipmtu Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes. Possible values: 576 to 1500.

eth_speed Control Gigabit Ethernet auto-negotiation allowed speeds. Possible values: AUTO, AUTO-100, 1000, 100, 10.

eth_duplex Control Ethernet auto-negotiation allowed duplex. Possible values: AUTO, FULL, HALF.

local_ip IPv4 address.

local_netmask IPv4 netmask.

default_gw IPv4 default gateway.

local_dnsip DNS server primary.

local_dnsip2 DNS server secondary.

use_dhcp Controls use of DHCP or static IP. Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).

local_hostname Network hostname.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, 1 on failure.

status String describing the failure when ret is 1. “OK” on success.

Set the maximum login limit.

mximum number of login limit. The limit is in range of ( greater than 2 and less than 100 )

Login window period, the value are considered as seconds. Max login attempts can be reached (Greater than 59 and less than or equal to 32768)

Locout interval value are mentioned in seconds value, which is used when maximum number of login limit is reached. The valuare ranges are ( -1 to 32768)

Login timeout

output: Updates the system login logout limits in the STATE table of the database

Set the nfs value in the database.

enable/disable nfs

provide the nfs server ip address. Default is 192.168.1.6

provide the server root path / location.

Output: update nfs information in the STATE_TABLE in the database

Set the SNMP value in the database

enable/disable SNMP

enable/disable power trap

enable/disable Input loss trap

enable/disable Input recover

enable/disable temperature high trap

enable/disable temperature recover trap

trap hosts value is the ipaddress. Default ip address value is 192.168.0.6

hiigh temperature default value is 30,

nominal temperature default value is 30,

enable/disable SNMP

SNMP v3 encrypt value

z3user

z3password

snmp v3 usrpro default value is md5

z3password

decrypt value

default value for engineid is 0.

Output : Update SNMP values in the SNMP_TABLE of the database.

Enable/Disable SNTP.

NTP server or list of NTP servers.

Linux TZ database value for Timezone.

Set the GPS NMEA data value in the database

enable/disable the NMEA

Output : Update the NMEA value in the STATE_TABLE of the database.

Enable/Disable ONVIF.

Enable/Disable ONVIF persistent audio channel.

Maximum ONVIF profiles to allow (1 or 2).

enable/disable video motion detection

sensitivity value required for vmd ( value will between 1 to 100)

enable/diable video motion and too darkness zone

crop width for VMD and too_darkness

crop height for VMD and too_darkness

crop startx for VMD and too_darkness

crop starty for VMD and too_darkness

enable/disable too darkness

threshold value for too darkness ( value will between 1 to 100)

channel number (1 / 2)

Output : update this value in the persistent configuration.

Set the RTSP value in the database

read rtsp port and the default value is 554

Timeout value required for the rtsp connection

Output : update rtsp values in the STATE_TABLE of the database

Set the term server value in the database

Enable/Disable remote access to terminal server. Possible values are : on, off

Enable/Disable shared access to terminal server. Possible values are : on, off

Output : Update rtsp values in the STATE_TABLE of the database

Set the video group configuration, and update in the database and change the active settings dynamically.

Is the camera index, the values are ( 4K. DME-20, HE2160-RPS ) and so on.

enable/disable noise reduction.

enable/disable crop region.

===
crop_x ===

crop rectangle x value

===
crop_y ===

crop rectangle y value

crop rectangle width value

crop rectangle height value
Output : Update the value in the VIDEO_GROUP_TABLE in the database.

Set the view port for the decoder and update in the database.

Decoder Channel number

viewport settings. The default value is fit.

Output: Updates the viewport settings for the given decoder instance in DECODER_TABLE of database

Set the vpss value in the database.

Enable or disable the VPSS mode

Output: Update the VPSS enable or Disable in STATE table of the database

Set the Wifi network and update in the databse.

ssid: Wifif SSID

psk: Wifi password

wifi_client_local_ip: Local IP addres ragne for WIFI network

wifi_client_local_local_netmask: Subnet mask to be used with Wifi network

wifi_client_default_gw: Default Gateway to be used with Wifi Network

wifi_client_use_dhcp: DHCP server to be used with Wifi network for DNS resolutions

Output: Updates the wifi network Access Point settings in State table of database

Possible values: off, on

Transition the encoder channel into the running state.

Once you start the channel, it will not transmit data until the
video input is detected.

St

Transition the encoder channel into the stopped state.

Read the current temperature status of cpu and lense.

Initially it checks the file cur_temp in the /tmp/ folder. If exist then it reads from the file

else it reads from the system call.

Output : Send the temperature status to update in the webui.

is password required or not.

Update the state of the required web login value in the STATE_TABLE of the database.

update the ptz value in the database.

parse the data using json format and retrieve the video source and row information .

Output: Updates the PTZ value in the ONVIF_Ptzs table of the database.

update the ptz preset value in the database.

parse the data using json format and retrieve the video source and row information .

Output : Update the row value in the PTZ_Preset table of the database

update the ptz tour spots value in the database.

parse the data using json format and retrieve the like ProfileToken, PresetTourToken, RowIndex, PresetDetailToken, PresetDetailHome, StayTime, pan,tilt, zoom, pspeed, tspeed and zspeed.

Output : Update the row value in the ONVIF_PtzTourSpots table of the database

Control serial port terminal server for VISCA

Possible values: client, server

Possible values: clearchannel, telnet

Local TCP port (for server mode)

Remote IP address (for client mode only)

Remote TCP port (for client mode only)

Possible values: 9600, 19200, 38400, 57600, 115200

username: name of the user

user level: user levels 0-7 to define the roles

password: user credentials

Output: Add the new user in ONVIF_users table of database

remove the user name from the database.

get the name of the user for e.g. guest and user level information from the ONVIF_users table in the database.

Output: Delete the user name in ONVIF_users table of database and update it.

data: Name of the user

Output: User level will be removed in ONVIF_users table of database

data: Name of the user

Output: User password will be removed in ONVIF_users table of database

Get the current camera exposure values through visca command.

chn Optional. The default is Camera 1. Select between connected cameras. Possible values: 1 = Camera 1, 2 = Camera 2.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, -1 on failure.

interface TEXT,

enable TEXT.

eap TEXT.

anonymous_identity TEXT.

identity TEXT.

password TEXT.

private_key_password TEXT.

Get the current camera exposure values through visca command.

chn Optional. The default is Camera 1. Select between connected cameras. Possible values: 1 = Camera 1, 2 = Camera 2.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, -1 on failure.

enable INTEGER,

cron TEXT.

func TEXT.

func_args TEXT.

type TEXT.

minutes INTEGER.

hours INTEGER.

day INTEGER.

month INTEGER.

cron TEXT.

Get the current camera exposure values through visca command.

chn Optional. The default is Camera 1. Select between connected cameras. Possible values: 1 = Camera 1, 2 = Camera 2.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, -1 on failure.

mounted TEXT,

Get the current camera exposure values through visca command.

chn Optional. The default is Camera 1. Select between connected cameras. Possible values: 1 = Camera 1, 2 = Camera 2.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, -1 on failure.

numerator INTEGER,

denominator INTEGER.

Get the current camera exposure values through visca command.

chn Optional. The default is Camera 1. Select between connected cameras. Possible values: 1 = Camera 1, 2 = Camera 2.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, -1 on failure.

logo_enable TEXT,

logo_filename TEXT.

logo_width INTEGER.

logo_height INTEGER.

logo_blob BLOB.

ico_blob BLOB.

model_enable TEXT.

model_name TEXT.

Get the current camera exposure values through visca command.

chn Optional. The default is Camera 1. Select between connected cameras. Possible values: 1 = Camera 1, 2 = Camera 2.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, -1 on failure.

preset TEXT,

enc_channels TEXT.

opmode TEXT.

enc_current_preset TEXT.

dec_current_preset TEXT.

Get the current camera settings from the Database.

chn Optional. The default is Camera 1. Select between connected cameras. Possible values: 1 = Camera 1, 2 = Camera 2.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, -1 on failure.

zoom_direct_value INTEGER.

white_balance_mode TEXT.

color_gain INTEGER.

color_hue INTEGER.

chroma_suppress INTEGER.

wb_manual_rgain_direct INTEGER.

wb_manual_bgain_direct INTEGER.

visca_localport TEXT.

optical_zoom_only BOOL. 0 or 1.

focus_direct_value INTEGER.

manual_focus TEXT.

flexio_localport TEXT.

exposure_mode INTEGER.

shutter INTEGER.

iris INTEGER.

gain INTEGER.

high_sensitivity INTEGER.

hlc_level INTEGER.

hlc_level_mask INTEGER.

stable_zoom INTEGER.

eflip INTEGER.

lr_reverse INTEGER.

monitor_mode TEXT.

genlock_source INTEGER.

manual_icr TEXT.

zoom_step_size INTEGER.

focus_step_size INTEGER.

img_freeze INTEGER.

hr_mode INTEGER.

img_stabilizer INTEGER.

img_bw INTEGER.

nr_2d_level INTEGER.

nr_3d_level INTEGER.

icr_threshold INTEGER.

slow_shutter BOOL. 0 or 1.

slow_shutter_limit INTEGER.

flicker_reduction BOOL. 0 or 1.

img_stabilizer_level INTEGER.

wide_dynamic_range TEXT.

ve_brightness TEXT.

ve_compensation_type TEXT.

ve_compensation_level TEXT.

tab_index TEXT.

imgvflip INTEGER.

imghflip INTEGER.

imgrotate INTEGER.

Get the current camera exposure values through visca command.

chn Optional. The default is Camera 1. Select between connected cameras. Possible values: 1 = Camera 1, 2 = Camera 2.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, -1 on failure.

ae_mode TEXT,

shutter TEXT.

iris TEXT.

gain_inquiry TEXT.

sensitivity TEXT.

hls_inquiry TEXT.

min_shutter INTEGER.

max_shutter INTEGER.

shutter_label TEXT.

min_iris INTEGER.

max_iris INTEGER.

iris_label TEXT.

min_gain INTEGER.

max_gain INTEGER.

gain_label TEXT.

Get the current camera monitor mode values from the visca command.

chn Optional. The default is Camera 1. Select between connected cameras. Possible values: 1 = Camera 1, 2 = Camera 2.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, -1 on failure.

modes TEXT.

current_mode TEXT.

Get the current decoder setting values from the database.

chn Optional. The default is Camera 1. Select between connected cameras. Possible values: 1 = Camera 1, 2 = Camera 2.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, -1 on failure.

preset TEXT.

channel INTEGER.

url TEXT.

aenable TEXT.

viewport TEXT.

latency_mode TEXT.

max_latency_ms TEXT.

srt_mode TEXT.

srt_latency TEXT.

srt_decrypt TEXT.

srt_pass TEXT.

zixi_fec TEXT.

zixi_fecoverhead TEXT.

zixi_fecblock TEXT.

zixi_latency TEXT.

zixi_decrypt TEXT.

zixi_pass TEXT.

rtsp_flags TEXT.

Get the downloaded files from the removable media.

chn Optional. The default is Camera 1. Select between connected cameras. Possible values: 1 = Camera 1, 2 = Camera 2.

job Optional. The job from the schedule tab.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, -1 on failure.

FileName TEXT.

FileSize TEXT.

LastModified TEXT.

Get the downloaded files from the removable media.

chn Optional. The default is Camera 1. Select between connected cameras. Possible values: 1 = Camera 1, 2 = Camera 2.

job Optional. The job from the schedule tab.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, -1 on failure.

color_pallette TEXT.

tab_index TEXT.

color_pallette_disabled TEXT.

Get the current camera exposure values through visca command.

chn Optional. The default is Camera 1. Select between connected cameras. Possible values: 1 = Camera 1, 2 = Camera 2.

JSON formatted table with values below

ret Custom return code of the HTTP POST request. 0 on success, -1 on failure.

preset TEXT,

channel INTEGER.

vbitrate TEXT.

vframeratediv INTEGER.

vsource TEXT.

vcodec TEXT.

vprofile TEXT.

vprotocol TEXT.

avmux_index TEXT.

vgdr TEXT.

vdest TEXT. aenable TEXT. acodec TEXT. abitrate TEXT. asamplerate TEXT. aport TEXT.

apair INTEGER.

vres TEXT.

vgopsize INTEGER.

vpid INTEGER.

apid INTEGER.

zixiauthen TEXT.

zixisession TEXT.

zixiuser TEXT.

zixioverhead TEXT.

zixifecblock TEXT.

zixilatency TEXT.

zixirateadjen TEXT.

fecrow INTEGER.

feccol INTEGER.

feconoff TEXT.

aptspcr INTEGER.

tslowlat TEXT.

tsrate TEXT.

pcrpid INTEGER.

pcrinterval INTEGER.

pmtpid INTEGER.

klvenable TEXT.

klvmode TEXT.

klvmuxmethod TEXT.

klvsrc TEXT.

klvbrate TEXT.

klvserialbaud TEXT.

klvpid TEXT.

vratectrl TEXT.

vdelay INTEGER.

storage TEXT.

fprefix TEXT.

asource TEXT.

authonoff TEXT.

auth_user TEXT.

auth_passwd TEXT.

auxonoff TEXT.

filesize TEXT.

nfstrength TEXT.

telopenable TEXT.

teloptext TEXT.

teloplocation TEXT.

telopcharsize TEXT.

teloptextcolor TEXT.

telopoutlineenable TEXT.

telopoutlinecolor TEXT.

gps_overlay_enable TEXT.

gps_overlay_device TEXT.

gps_overlay_location TEXT.

gps_overlay_char_size TEXT.

pipenable TEXT.

piplocation TEXT.

vquality TEXT.

vinterlacemode TEXT.

vmulticastdest TEXT.

amulticastdest TEXT.

rtsp_auth_enable TEXT.

rtsp_auth_username TEXT.

rtsp_auth_password TEXT.

rtsp_transport_mode TEXT.

lowdelay_opt TEXT.

vcropaspect TEXT.

vcrop_enable TEXT.

vcrop_width INTEGER.

vcrop_height INTEGER.

vcrop_x INTEGER.

vcrop_y INTEGER.

rotate_enable INTEGER.

rotate_angle INTEGER.

rtmp265_enable TEXT.

srt_pass TEXT.

srt_encrypt INTEGER.

srt_mode INTEGER.

srt_destAddr TEXT.

mmulticastdest TEXT.

mport TEXT.