Differences

This shows you the differences between two versions of the page.

--- http_qcom [2023/05/08 15:07]
suresh
+++ http_qcom [2023/05/11 21:17]
johnw [SaveCamera]
@@ Line 807: / Line 807: @@
 Save camera-related settings below.
-=== zoom_direct_value ===
+===     zoom_direct_value     ===
 Description: Set camera zoom
@@ Line 856: / Line 856: @@
 Possible values: auto, manual
-==== SetIp ====
-=== local_ip ===
-IPv4 adresss
-=== local_netmask ===
+==== SetIp ====
+----
-IPv4 netmask
-=== default_gw ===
-IPv4 default gateway
-=== local_dnsip ===
-DNS server primary
-=== local dnsip2 ===
-DNS server secondary
-=== use_dhcp ===
-Controls use of DHCP or static IP
+Control networking settings of the Z3 device such as local IPv4 IP address, netmask, etc.
+Additionally control Encoder Auto-Start after boot-up and enable/disable showing of advanced WebUI settings.
-Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP)
+\\
-=== do_autostart ===
+== Parameters: ==
+----
+**//do_autostart//**
+Control automatic stream start after bootup.
+Possible values: 1 = do autostart 0 = do not autostart.
-Control automatic stream start after bootup
+**//enc_adv_setting//**
+Control appearance of advanced settings on WebUI.
+Possible values: off, on.
-Possible values: 1 = do autostart 0 = do not autostart
+**//ipmtu//**
+Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes.
+Possible values: 576 to 1500.
-=== enc_adv_setting ===
+**//eth_speed//**
+Control Gigabit Ethernet auto-negotiation allowed speeds.
+Possible values: AUTO, AUTO-100, 1000, 100, 10.
-Control appearance of advanced settings on WebUI
+**//eth_duplex//**
+Control Ethernet auto-negotiation allowed duplex.
+Possible values: AUTO, FULL, HALF.
-Possible values: off, on
+**//local_ip//**
+IPv4 address.
-=== eth_speed ===
+**//local_netmask//**
+IPv4 netmask.
-Control Gigabit Ethernet auto-negotiation allowed speeds
+**//default_gw//**
+IPv4 default gateway.
-Possible values: AUTO, AUTO-100, 1000, 100, 10
+**//local_dnsip//**
+DNS server primary.
-=== eth_duplex ===
+**//local_dnsip2//**
+DNS server secondary.
-Control Ethernet auto-negotiation allowed duplex
+**//use_dhcp//**
+Controls use of DHCP or static IP.
+Possible values: 1 (DHCP enabled), 0 (DHCP disabled, use static IP).
-Possible values: AUTO, FULL, HALF
+**//local_hostname//**
+Network hostname.
-=== ipmtu ===
+\\
+== Returns: ==
+----
+JSON formatted table with values below
-Control Ethernet IP Maximum Transmission Unit (MTU) size in bytes
+**//ret//** Custom return code of the HTTP POST request. 0 on success, 1 on failure.
-Possible values: 576 to 1500
+**//status//** String describing the failure when **ret** is 1. "OK" on success.
+\\
 ==== SetDisplay ====
@@ Line 1044: / Line 1051: @@
 ==== GetStatus ====
-=== return the encoder status ===
+return the encoder status
-input : channel_number
+**input** : channel_number
-return value : Can be running / couldn't deduct input on camera / idle / Stopped
+**Output ** : The encoder status can be **running / couldn't deduct input on camera / idle / Stopped. **
+The encoder status values are stored in this path /tmp/enc_1_status.
 ==== ClearHistory ====
-delete decoder history
+delete the decoder history
-input : channel number
+**input** : channel number
-output : success / failure
+**output** : Delete the channel number from the DECODER_HISTORY_TABLE of the database
 ==== AddHistory ====
 Insert decoder history in the database
-Input : channel number, URL
+**Input** : channel number and URL
-Output : Add the information in the decoder history table in the database
+**Output** : Add the information in the DECODER_HISTORY_TABLE in the database
 ==== SetAudio ====
 Set the analog mic decibal value
-Input : analog gain decibal value (Range -97 to 30)
+**Input : **
-Output : update audio input table in the database
+analog gain decibal value (Range -97 to 30)
+Output : update the value in the AUDIO_INPUT_TABLE in the database
 ==== LoadUser ====
@@ Line 1566: / Line 1575: @@
 enable/disable crop region.
-=== \\
+===\\
 crop_x ===
 crop rectangle x value
-=== \\
+===\\
 crop_y ===
@@ Line 1584: / Line 1593: @@
 crop rectangle height value\\
 Output : Update the value in the VIDEO_GROUP_TABLE in the database.
-====   ====
 ==== GetCameraLink ====
+Read the value of color table using the system call and pixel format
+from the fpga.
 ==== SetCameraLink ====
+Set the value of color table and pixel format and update in the CAMERALINK_TABLE of the database.
+====   ====
 ==== RemoveJobs ====
+Remove / delete the jobs from the schedule.
+=== purgelist ===
+Read the job index and job name
+=== rowcnt ===
+Number of rows of the schedule job.
+=== Output ===
+Delete the jobs in the /opt/config/z3schedules/root/ in the system and also update in the SCHEDULE_TABLE in the database.
 ==== SaveJobs ====
+Read the values from the schedule tab and save the jobs
+=== data ===
+The data contains multiple values, such as
+enable/disable of schedule
+Name of the job
+Function are (Start-Encoder / Stop-Encoder / Snapshot / PTZ Preset / PTZ Tour / Reboot)
+Channel (Ch1 / Ch2 / Ch3 / Ch4)
+Options about the time, which can be (Every Minute / hours / day / Week/ Month/ Yearly / custom )
+=== rowcnt ===
+Number of rows of the schedule job.
+=== Output ===
+Save the jobs in the /opt/config/z3schedules/root/ in the system and also update in the SCHEDULE_TABLE in the database.
 ==== GetVideoInputs ====

Wiki

User Tools

Site Tools

Differences

Page Tools